Wired loop of 60 m perimeter to be installed in a triangle. Delivered...
Wired loop of 60 m perimeter to be installed in a square. Delivered with...
27 MHz 1/4 wave vertical antenna delivered with 3 wire radians. Very...
28 MHz 1/4 wave vertical antenna delivered with 3 wire radians. Very...
21 MHz 1/4 wave vertical antenna delivered with 3 wire radians. Very...
21 MHz 1/4 wave vertical antenna delivered with 3 wire radians. Very...
Voltage Balun ratio 1:1 (ex: 50 => 50 ohms). Maximum power: 1000 W PEP, to make "inverted V" dipole antennas. Robust aluminum body diameter: 5 cm (thickness: 2mm), real HF ferrite toroid and SO-239 connector.
Multiband dipole antenna designed for transmitting/receiving on bands between 14 MHz and 60 MHz. Its power rating is 500 watts PEP and its total length is 8 m.
LWA, HF Wideband Antenna (3 to 30 MHz) is perfect for the garden or portable SSB/CW operations ; week-end, holidays... It is a non adjustable antenna, lenght : 20 m, maximum power : 500 W PEP.
Yagi antenna 3 elements for the reception of aeronautical distress beacons on 121,5 MHz. Very robust, elements made of solid rods of 8 mm, radiator in 12 mm tube and square boom of 25 mm side (2 mm thick) and rear handle for pedestrian use. Robustness and performance guaranteed !
Double Conrad Windom, all bands OM HF + CB + 50 MHz; 1.8/3.5/5/7/10/14/18/21/24/27/28 and 50 MHz (with coupler depending on installation), lengths: 82 + 28 m. Robust aluminum balun (⌀ 5 cm / thickness: 2 mm) with SO-239 connector, 2.5 mm2 flexible copper wires in insulating sheath and insulator at the ends. Can be used fixed or portable, inverted-V,...
The LCB is designed on the basis of the TTFD, in addition to a central fixing bar for horizontal installation on a mat. It is therefore possible to install another antenna (VHF/UHF for example) above the LCB.
Triple "Full size" dipole 1/2 wave 7/14 and 21 MHz, lengths : 2x10,8 + 2x5,4 + 2x3,8 m (6 wires). Robust aluminum balun with SO-239 (PL) connector and insulators at the ends.
Dipole folded over non-inductive load operating from 3 to 30 MHz, length : 22 m, maximum power : 800 watts PEP, intended for users wishing an antenna quickly operational, broadband and without adjustment: military, professional, amateur radio, SWL, etc. It is also an interesting compromise in case of lack of space...
Impedance transformer (1:9 ratio) to transform a long wire into a multiband antenna. Use with automatic or manual coupler recommended. It is the ideal solution to transmit during the week-end or the holidays. Discretion assured with its camouflage color.
Coaxial cables, from 50 cm, made of RG-213/U Mil-C-17 (international military standard), 10.3 mm diameter coaxial cable and equipped with 2 "high quality" Stecker connectors with Teflon insulation and gilded soul. Assembled and tested before shipment. Choose length =>
1:32 ratio balun intended for Maxiwhip type antenna design for low band reception. The Maxiwhip is a vertical antenna consisting of an aluminum whip of about ten meters or a wire wound along a fishing rod and two (or more) radians of the same length.
21 MHz 1/4 wave vertical antenna delivered with 3 wire radians. Very robust tubes with large diameters and thicknesses (2 and 1,5 mm), wide bandwidth, very low SWR. Connection to the 50 ohm coaxial cable directly by SO-239 (no balun or other adaptation system). On perfect ground the gain reaches 5.15 dBi and the radiation lobes favor DX.
Multiband dipole antenna designed for transmitting/receiving on bands between 7 MHz and 30 MHz. Its power rating is 500 watts PEP and its total length is 15 m.
Impedance transformer (1:4 ratio) to transform a short wire (6 m minimum) or an aluminium tubing into a multiband antenna. Use with automatic or manual coupler recommended. It is the ideal solution to transmit during the week-end or the holidays. High Power version (750 W PEP) + Choke balun.
Balun ratio 1:9 (50 => 450 ohms) to go from a 50 ohm coaxial cable to a twin-lead 450 ohm bifilar line, max. 1000W PEP. Real HF ferrite toroid and SO-239 connector
14 MHz/2 element monoband Yagi antenna, space-saving, combining performance and robustness of construction. "All grounded" design greatly reducing atmospheric QRM in reception (static). Easy adjustment by gamma-match.
Wired loop with a perimeter of 43 m to be installed in a square. Delivered with its 1/4 balun and 4 insulators. Can be used on the upper bands subject to sufficient clearance from the ground (10 m minimum) or tuner.
Delta-loop antenna, the "queen of DX", monoband 14 MHz/2 elements combining performance and robustness of construction. "All grounded" design greatly reducing atmospheric QRM in reception (static). Easy adjustment by gamma-match.
Vertical antenna 121.5 MHz, 1/4 wave, aluminum, delivered set. To be installed on a mast 35 to 40 mm in diameter.
Wire dipole 40/80 m (7/3.5 MHz) made of 2.5 mm2 flexible wire, equipped with 2 coaxial traps, a balun 1:1 and insulators at the ends. Wide bandwidth and easy adjustment.
Wall bracket for grounding radio station equipment. This aluminum strip is equipped with 7 screws of 30 mm with wing nuts and is fixed to the wall by means of 3 holes. Delivered without connector (optional). Grounding the equipment ensures operator safety and better station performance.
Double dipole 1/2 wave 18 and 24 MHz for amateurs of the WARC bands, lengths : 9 + 6 m (4 wires). Robust aluminum balun with SO-239 (PL) connector and insulators at the ends.
Wired loop of 60 m perimeter to be installed in a square. Delivered with its 1/4 balun and 4 insulators. Can be used on the upper bands subject to sufficient clearance from the ground (10 m minimum) or tuner.
Delta-loop antenna, the "queen of DX", monoband 50 MHz/3 elements combining performance and robustness of construction. "All grounded" design greatly reducing atmospheric QRM in reception (static). Compact and easy to adjust with its gamma-match.
Conrad Windom, Amateur Radio & CB bands: 3.5/7/14/18/24/27/28/50 and 70 MHz (with coupler depending on installation), length: 42 m. Robust aluminum balun (⌀ 5 cm / thickness: 2 mm) with SO-239 connector (PL female), flexible 2.5 mm2 copper wires in insulating sheath and insulator at the ends. Can be used fixed or portable, inverted-V, horizontal or Sloper.
Fixing set consisting of 2 thick aluminum plates and screws necessary to install an antenna (of any brand ...) with a square boom 30 mm side on a mast 40 to 50 mm in diameter.
8.25 m "versatile" whisk delivered with HF BOX and 1 wired radian. Can be used in high or low impedance from 3.5 to 70 MHz. Aluminum tubes, diameter 40 to 16 mm and weight 6.5 kg. Can be used with coaxial cable, single wire or "twin-lead" depending on the tastes ... Provide a suitable manual or automatic coupler.
The TACTICAL antenna is a dipole folded over a non-inductive load resistor. It is designed to operate from 1 to 30 MHz but especially for an optimal efficiency on low bands, below 10 MHz. It is intended for users who want a fast, operational, broadband and unadjusted antenna : military, professional, SWL, etc.
Voltage Balun ratio 1:6 (ex: 50 => 300 ohms). Maximum power: 1000 W PEP, to make Conrad Windom and folded dipole antennas. Robust aluminum body diameter: 5 cm (thickness: 2mm), real HF ferrite toroid and SO-239 connector.
Dipole 1/2 wave 7 MHz shortened, length: 13 m. Robust aluminum balun with SO-239 connector and insulators at the ends + CHOKE BALUN integrated.
![]() | ExpeditionsOur goods are shipped by Colissimo International or carrier depending on the weight, value and / or the size of the parcel |
![]() | Contact usYou can contact us 24/7 by e-mail: https://ita-antennas.com/en/contact-us |
![]() | PaymentYou can pay by credit card, Paypal or bank transfer |
![]() | VATThe prices displayed on the site are "net" |